Polygon with holes
![](http://upload.wikimedia.org/wikipedia/commons/thumb/c/c9/Polygons_with_holes.png/350px-Polygons_with_holes.png)
In geometry, a polygon with holes is an area-connected planar polygon with one external boundary and one or more interior boundaries (holes).[1] Polygons with holes can be dissected into multiple polygons by adding new edges, so they are not frequently needed.
An ordinary polygon can be called simply-connected, while a polygon-with-holes is multiply-connected. An H-holed-polygon is H-connected.[2]
Degenerate holes
[edit]Degenerate cases may be considered, but a well-formed holed-polygon must have no contact between exterior and interior boundaries, or between interior boundaries. Nondegenerate holes should have 3 or more sides, excluding internal point boundaries (monogons) and single edge boundaries (digons).
Boundary orientation
[edit]Area fill algorithms in computational lists the external boundary vertices can be listed in counter-clockwise order, and interior boundaries clockwise. This allows the interior area to be defined as left of each edge.[3]
Conversion to ordinary polygon
[edit]A polygons with holes can be transformed into an ordinary unicursal boundary path by adding (degenerate) connecting double-edges between boundaries, or by dissecting or triangulating it into 2 or more simple polygons.
Example conversion of a single-holed polygon by connecting edges, or dissection
In polyhedra
[edit]Polygons with holes can be seen as faces in polyhedra, like a cube with a smaller cube externally placed on one of its square faces (augmented), with their common surfaces removed. A toroidal polyhedron can also be defined connecting a holed-face to a holed-faced on the opposite side (excavated). The 1-skeleton (vertices and edges) of a polyhedron with holed-faces is not a connected graph. Each set of connected edges will make a separate polyhedron if their edge-connected holes are replaced with faces.
The Euler characteristic of hole-faced polyhedron is χ = V - E + F = 2(1-g) + H, genus g, for V vertices, E edges, F faces, and H holes in the faces.
- Examples
-
(genus 0) with two 1-holed-faces (top and bottom).
V=16, E=20, F=8, H=2.
3-connected -
Toroid (genus 1) with two 1-holed-faces.
V=16, E=24, F=10, H=2.
2-connected -
(genus 0) with one 1-holed-face.
V=16, E=24, F=11, H=1.
2-connected -
(genus 0), with six 1-holed faces.
V=32, E=36, F=12, H=6.
7-connected -
Toroid (genus 5), with six 1-holed faces.
V=40, E=72, F=30, H=6.
2-connected -
Toroid (genus 2) with two 2-holed-faces.
V=24, E=36, F=14, H=4.
3-connected -
Toroid (genus 1) with one 2-holed-face, and one 1-holed-face.
V=24, E=36, F=15, H=3.
3-connected -
(genus 0) with one 2-holed-face.
V=24, E=36, F=16, H=2.
3-connected -
Toroid (genus 1) with two 1-holed-faces.
V=24, E=36, F=14, H=2.
2-connected -
Toroid (genus 1) with two 1-holed-faces.
V=32, E=48, F=18, H=2.
2-connected
- Examples with degenerate holes
A face with a point hole is considered a monogonal hole, adding one vertex, and one edge, and can attached to a degenerate monogonal hosohedron hole, like a cylinder hole with zero radius. A face with a degenerate digon hole adds 2 vertices and 2 coinciding edges, where the two edges attach to two coplanar faces, as a dihedron hole.
See also
[edit]- Prince Rupert's cube — largest cube that can pass through a unit cube's hole.
References
[edit]- ^ Somerville, D. M. Y. (1929), "IX.4: Polyhedra with ring-shaped faces", An Introduction To The Geometry Of Dimensions, Methuen & Co., pp. 144–145
- ^ O'Rourke, Joseph (1987), "Chapter 5: Holes" (PDF), Art Gallery Theorems and Algorithms, International Series of Monographs on Computer Science, vol. 3, Oxford University Press, pp. 125–145, ISBN 0-19-503965-3
- ^ Urrutia, Jorge (2000), "Art Gallery and Illumination Problems", Handbook of Computational Geometry, Elsevier, pp. 973–1027, doi:10.1016/b978-044482537-7/50023-1, ISBN 9780444825377